Make DIY String... Outdoors Design Home

Would you like to add some light and interest to your garden landscape? You can do this easily by making DIY string light poles with concrete stands. These poles will not only provide beautiful light, but they will also add a touch of elegance to your outdoor space. Best of all, they are easy and inexpensive to make! Read on for instructions on how to create your own string light poles.

Gather Your Supplies

DIY String light

You’ll be the envy of your neighborhood with these stately string light poles decorating your garden landscape. Not only are they lovely to look at, but they’re easy and inexpensive to make yourself. You’ll need a few supplies before you get started, though.

Most importantly, you’ll need a concrete mix, rebar, and string lights. You can find these items at any hardware store. Once you have your supplies, simply follow the instructions below to create your own beautiful string light poles.

Drill a Hole in the Centre of Each Concrete Block

DIY String light

To drill a hole in the center of each concrete block, use a power drill with a masonry bit. First, mark the spot where you want to drill the hole. Next, put on safety goggles and gloves to protect yourself from flying debris. Then, position the drill bit on the mark and start drilling. Apply steady pressure as you drill, and try to keep the drill perpendicular to the surface of the block.

Once you’ve drilled through the block, lift the drill out of the hole and brush away any loose debris. Finally, vacuum up any dust that remains before moving on to the next block. With a little practice, you’ll be able to quickly and easily drill holes in concrete blocks.

Insert the Metal Pole into the Hole

DIY String light

A metal pole inserted into a hole is more likely to stay straight if extra care is taken during the insertion process. It’s important to make sure that the hole is wide enough and deep enough to accommodate the entire pole. The depth of the hole should be at least equal to the length of the pole, and the width should be slightly larger than the diameter of the pole.

It’s also important to make sure that the hole is lined up with where you want the pole to go; otherwise, you’ll have a difficult time getting it straight.

Once you’ve double-checked the position of the hole, slowly lower the pole into it. Start by aligning one end of the pole with the edge of the hole, then lower it straight down. If you find that the pole isn’t going in straight, gently wiggle it until it’s aligned, then continue lowering it down.

Be careful not to let the pole bend as you’re lowering it; otherwise, you’ll have a harder time getting it straight later on. Once the metal pole is inserted into the hole, stop and check that it’s still straight before continuing.

Pour Concrete Mix into Each Block, Filling to the Top

DIY String light

Before you begin, it’s important to have all of your materials gathered and Ready. You will need a concrete Mix, water, and a trowel. Once you have everything, you’re ready to Start filling your block.

Simply pour the concrete mix into each block, filling it to The top. Then, use your trowel to smooth it out. After that, all you need to Do is add water and wait for the concrete to set. That’s all there is to it! With just a little bit of effort, you can create strong, durable blocks that will last for years to come.

Allow the Concrete to Dry Completely Before Using

DIY String light

Concrete is a reliable and durable building material that can be used for a variety of applications such as concrete bases for light poles. However, it is important to allow the concrete to dry completely before using it. Otherwise, the concrete may not be as strong as it should be and could crack or crumble over time. In addition, concrete that has not been allowed to dry properly can be more susceptible to water damage.

As a result, it is essential to be patient and wait for the concrete to fully dry before putting it to use. Doing so will ensure that your concrete structure will be able to withstand the elements and last for many years to come.

Hang Your String Lights from the Metal Poles

DIY String light

Hang your string lights from the metal poles in your backyard to add a touch of class to your outdoor space. String lights are a great way to highlight your landscaping or add a bit of ambiance to your next outdoor party. And while you can always just prop them up on the ground or drape them over a fence, hanging them from metal poles gives your yard a polished look.

Plus, it’s easy to do! Just use metal hooks or zip ties to attach the lights to the poles. Then, plug in the lights and enjoy their glow!

In Summary

Hang your globe string lights year-round by following these simple steps! Now that you know how to make your own concrete light poles, you can customize them to match any outdoor décor. Get creative and have fun with it – the possibilities are endless!